cany Posted July 24, 2015 Share Posted July 24, 2015 Thanks Bebop They seem to have the lowest price too Link to comment Share on other sites More sharing options...
cany Posted August 21, 2015 Share Posted August 21, 2015 I give up on my original invader this thing is possessed Its not even reading nickle coils now Link to comment Share on other sites More sharing options...
Bebop Posted August 21, 2015 Share Posted August 21, 2015 Mine has been running really well for 3 months now. I've had no problems running it in normal or TC mode. however,.....(yeah, I know) .....just yesterday it shut itself off unexpectedly. It did it twice., but started right back up. Then this morning, I fired it up and the display screen was scrambled. Uh oh..... I pulled the battery and re fired it up. It's been working normally all day with no problems. My fingers are crossed.... Link to comment Share on other sites More sharing options...
cany Posted August 21, 2015 Share Posted August 21, 2015 I been whacking in on concrete that seems to help get it back to normal for a little while Bebop 1 Link to comment Share on other sites More sharing options...
cany Posted August 22, 2015 Share Posted August 22, 2015 Question the top cap that the tank screws into does that act as some kinda ground? Link to comment Share on other sites More sharing options...
cany Posted August 22, 2015 Share Posted August 22, 2015 Question the top cap that the tank screws into does that act as some kinda ground?Anyone Come on guys I know one of you must know Link to comment Share on other sites More sharing options...
cany Posted August 23, 2015 Share Posted August 23, 2015 Ok I know you Guys think Im nuts but hear me out................Ive had om going issues with my invader mini since day one I tried everything to fix it bu today it hit me I tried holding the tank pin?> to the center pin on the invader.............. No atomizer,,,,,,,,,,,,,,, ok what I been going thru (amongst other issues) so I says to my self, Self theres gotta be a connection here So I took the 510 connection thingy off the invader and took a look low n behold I saw a bit or black rubber in the threads (from the Bat covering?) So I figured Maybe iM GETTING A BAD CONNECTION? So I cleaned all the threads/connections up and low n behold Ive had no issues for the past few hrs? Now Imn sure this will change as my invader is possessed One can only hope I figured out the issue with it Bebop and jasonculp 2 Link to comment Share on other sites More sharing options...
Bebop Posted August 23, 2015 Share Posted August 23, 2015 Yes. It is the ground connection.😃 The moral of the story is keep those threads clean........ On any tank. Link to comment Share on other sites More sharing options...
cany Posted August 23, 2015 Share Posted August 23, 2015 Thanks Bebop as of now its still working But i DID order a new blue one from Vapenw yesterday just incase Hell I cant have enough of these things Bebop 1 Link to comment Share on other sites More sharing options...
cany Posted August 30, 2015 Share Posted August 30, 2015 When you guys shut yours off does it ask new/same coil everytime? Link to comment Share on other sites More sharing options...
Bebop Posted August 30, 2015 Share Posted August 30, 2015 Pretty sure. Yes Link to comment Share on other sites More sharing options...
cany Posted August 30, 2015 Share Posted August 30, 2015 Phewww thought my new invader was possessed too If I hit new coil (even though its the same one) the ohms jump up and I get a hotter vape even though its the same coil thats been in it Link to comment Share on other sites More sharing options...
Bebop Posted August 30, 2015 Share Posted August 30, 2015 ???Ni coil? Link to comment Share on other sites More sharing options...
cany Posted August 30, 2015 Share Posted August 30, 2015 Yup NI coil Link to comment Share on other sites More sharing options...
Bebop Posted August 30, 2015 Share Posted August 30, 2015 The ohms jump around a little on coils. Especially Ni and especially if recently used What are your settings? Link to comment Share on other sites More sharing options...
cany Posted August 30, 2015 Share Posted August 30, 2015 The ohms jump around a little on coils. Especially Ni and especially if recently used What are your settings?24W 420-460 temp Link to comment Share on other sites More sharing options...
Bebop Posted August 30, 2015 Share Posted August 30, 2015 Yep. Thats about where I hang out as well. I find a cold coil reads higher at first. Then the ohms will drop with use. If I put it down for a while the ohms will read a bit higher again. I have since learned not to pay too much attention to the man behind the curtain. I just click my button three times and repeat "there"s no vape like .1 ohm, there's no vape like .1 ohm" Link to comment Share on other sites More sharing options...
cany Posted August 30, 2015 Share Posted August 30, 2015 Yep. Thats about where I hang out as well. I find a cold coil reads higher at first. Then the ohms will drop with use. If I put it down for a while the ohms will read a bit higher again. I have since learned not to pay too much attention to the man behind the curtain. I just click my button three times and repeat "there"s no vape like .1 ohm, there's no vape like .1 ohm"LOL............Mine drop as well Im using the stock ni-occ coils now Link to comment Share on other sites More sharing options...
cany Posted September 15, 2015 Share Posted September 15, 2015 Ok Invader owners you vaping away in TC alls good then you realize your out of juice. Whats your procedure for refilling the tank? Im having coil issues again and its pissing me off Link to comment Share on other sites More sharing options...
cany Posted September 15, 2015 Share Posted September 15, 2015 After I take the tank off or change the batt I cant get the coil back to where it was its too cool if I hit same coil or Too hot/burnt if it hit new coil Link to comment Share on other sites More sharing options...
Bebop Posted September 15, 2015 Share Posted September 15, 2015 I don't know what you mean, cany. "Can't get the coil back"? If I change battery or put tank back on after refilling, I hit "new coil" and it reads the coil and here we go. Nothing changes for me. Link to comment Share on other sites More sharing options...
cany Posted September 15, 2015 Share Posted September 15, 2015 I don't know what you mean, cany. "Can't get the coil back"? If I change battery or put tank back on after refilling, I hit "new coil" and it reads the coil and here we go. Nothing changes for me. If I hit new coil it jumps to like 1.7 1.8 then I let it settle before fireing it will settle back around 1.2 1.3 but at the end of my hit its all nasty and burnt Its not a smooth warm vape like it was before Now I shut it down hit new coil it stayed at 1.2 but I got a crap cool vape Link to comment Share on other sites More sharing options...
Bebop Posted September 15, 2015 Share Posted September 15, 2015 Hmmm..... I do know that in TC mode if you don't let the coil cool completely you will get a false reading on a new read. You have to let the coil cool. Or suck through it like crazy without firing it to cool the coil before getting a fresh reading. Link to comment Share on other sites More sharing options...
cany Posted September 15, 2015 Share Posted September 15, 2015 Hmmm..... I do know that in TC mode if you don't let the coil cool completely you will get a false reading on a new read. You have to let the coil cool. Or suck through it like crazy without firing it to cool the coil before getting a fresh reading.Thats only when choosing new coil? Link to comment Share on other sites More sharing options...
Bebop Posted September 15, 2015 Share Posted September 15, 2015 As far as I know. I always do new coil as I want a fresh reading each time. But that's just me. Link to comment Share on other sites More sharing options...
Recommended Posts