vaping_jake Posted January 16, 2015 Posted January 16, 2015 I am trying to understand the rebuild process, but currently stuck on oneof the rules. Torch your coils. The only reasons I can think of : 1) it makes it either easier to wrap or or maintain the wrap or maybe both or 2) not to get a metallic taste on your vape SO the question I ask is what is the reason for it.
Compenstine Posted January 16, 2015 Posted January 16, 2015 As you said it takes the spring out of the wire. This makes it easier to wrap. You want to do this after it is wrapped to tighten up the coils too. This is done when making macro, micro and low ohm builds. Once installed, you will heat the coil up again with the battery to tighten it up more. You also also do this to make sure it is glowing from the inside out. Tug 1
fishguy1123 Posted January 16, 2015 Posted January 16, 2015 It's important to note that when heating the coil on the device not to pinch the coil while pressing the button unless you have ceramic tweezers. tazl37 1
Mplough Posted January 16, 2015 Posted January 16, 2015 Ah *slaps forehead*, that's what they're for.
joejoevapekins Posted January 16, 2015 Posted January 16, 2015 I need a new pair of tweezers and a ohm meter. Led is going out on mine
fishguy1123 Posted January 17, 2015 Posted January 17, 2015 Ah *slaps forehead*, that's what they're for. And all this time you've been plucking nose hairs with them.... lol jasonculp and Mplough 2
Tam Posted January 17, 2015 Posted January 17, 2015 I need a new pair of tweezers and a ohm meter. Led is going out on mine Mine too. Ceramic tweezers would be better than the extra fine needle nosed pliers I've been using - it puts out too much force and I wind up squishing my coils more than I wanted.
Mplough Posted January 17, 2015 Posted January 17, 2015 And all this time you've been plucking nose hairs with them.... lol Actually I have a trimmer for that. Seriously though I thought it was to keep heat from traveling up the arms, I never assumed anyone would squeeze them while applying power.
Compenstine Posted January 17, 2015 Posted January 17, 2015 You do get better results buy heating as you squeeze it. I don't have ceramic tips so I have to heat 3-4 times to do the same thing you could do 1-2 times with the ceramic tipped tweezers. Tam 1
Tam Posted January 17, 2015 Posted January 17, 2015 I torch the wire first and then wind it into a coil. Once that's done I squeeze and torch at the same time. Torching the wire first takes a lot of the springiness out of the wire so it holds its shape better after you wind it.
Compenstine Posted January 17, 2015 Posted January 17, 2015 I do the same Tam. But seems every time I install the coil it spreads a bit. That is why I heat and squeeze again after I install it. Tam 1
Earthling789 Posted January 17, 2015 Posted January 17, 2015 You mean packing the wire in ice for an hour, wrapping over and over against the grain, and then forcing the coil into a vice isn't the proper way??
Tam Posted January 17, 2015 Posted January 17, 2015 You mean packing the wire in ice for an hour, wrapping over and over against the grain, and then forcing the coil into a vice isn't the proper way?? We all have our own favorite ways to do things, Earthling.
joejoevapekins Posted January 17, 2015 Posted January 17, 2015 I no longer torch my coils. Just wrap and grab both leads with vise grips and give a good pull. Install pulse and squeeze
Compenstine Posted January 17, 2015 Posted January 17, 2015 That is for bread ties only Earthling. LMAO joejoevapekins and Tam 2
Mplough Posted January 17, 2015 Posted January 17, 2015 (edited) In theory, wouldn't having small gaps between the windings give better airflow to the cotton in the coil to help prevent scorching? Edited January 17, 2015 by Mplough
Compenstine Posted January 17, 2015 Posted January 17, 2015 I have found that having the gap does not allow the coil to vaporize the liquid as well. This allows the coil to clog up faster. Tam 1
Earthling789 Posted January 17, 2015 Posted January 17, 2015 I have found that having the gap does not allow the coil to vaporize the liquid as well. This allows the coil to clog up faster. I agree with this... The more space between wraps, only allows char and gunk to build up. Tighter wraps get hotter... I use to be a lighting engineer, and one thing about coil building for Halogen lighting is to minimize the gap for the hottest, brightest coil... and then figuring out the gas mixture, volume, pressure, and bulb-wall-thickness to maximize life (and minimize explosion).
vaping_jake Posted January 17, 2015 Author Posted January 17, 2015 Thanks all. In terms of gaps, i believe since we seek current flow which is based on "skin effect" that gaps would hinder the desired performance. Now I maybe dating myself here, but in the past when prototyping micro controllers we use to use a wire wrap tool. It would make a very nice tight coil around a post. perhaps this might help produce better wraps, just a theory. The tool would cost any where from $3 and up.
Tam Posted January 17, 2015 Posted January 17, 2015 There are coilers made specifically for wrapping coils for vaping available. Your idea is a good one, though!
Earthling789 Posted January 17, 2015 Posted January 17, 2015 Kuro Koiler is a cool manual winding tool... but they are pricey if you buy them in the US... $20 each, and there's a set of 3. Fasttech has the full set for < $7 I have one of those electronics wire tools somewhere in storage, but for $7, I just bought the spiffy ones from Fasttech
Tam Posted January 17, 2015 Posted January 17, 2015 I have a Q-coiler, which works well for me but it's a bit bigger than I like. At first, I thought the bigger size would be good, but as time has gone by, I'm leaning more toward the Kuro Koiler that Earthling mentioned as being more convenient.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now