jsr27 Posted August 24, 2014 Share Posted August 24, 2014 I'm using a vamo v5 and just bought some real Panasonic 18650 batteries and just noticed that its heating up when I vape on it a few times. Is this normal? What should I do? Link to comment Share on other sites More sharing options...
charles vapor Posted August 25, 2014 Share Posted August 25, 2014 what set up are you using? because if you are using low ohm coils I would not use panasonic batteries. Link to comment Share on other sites More sharing options...
Tam Posted August 26, 2014 Share Posted August 26, 2014 what set up are you using? because if you are using low ohm coils I would not use panasonic batteries. I routinely use Panasonic 18650 batteries in my mech mods with 1.5 or 1.8 ohm coils with no problem. Why shouldn't you do this? Link to comment Share on other sites More sharing options...
Earthling789 Posted August 26, 2014 Share Posted August 26, 2014 I routinely use Panasonic 18650 batteries in my mech mods with 1.5 or 1.8 ohm coils with no problem. Why shouldn't you do this? Tam, I'll assume Charles' statement was meant for sub-ohming? All the Panasonic batteries I have are rated at 10A, which (in a mechanical MOD) are perfectly safe for any coils over 1.0 Ohms. At 10A limits, the lowest coil these batteries could handle would be 0.45 Ohm, but I'd not trust them on anything lower than 0.8 Ohm (5.25A @ 4.2V), just to give a margin of safety by the "Rule of Two" - Use a battery of at least twice the load/discharge capacity of your expected average load. Now, specs on the Vamo V5 max at 6V, and is limited at 15W, The lowest coil resistance stated it can fire is 1.2 Ohms, and circuitry limits Amp output to 3.2A loads... which means Panasonic batteries are well within the operational limitations of the Vamo V5, and 3.2A should NOT heat up a 10A battery! To JSR27... More info would be handy to have... 10A Panasonic batteries should not be heating up your Vamo even if you push it to it's operational limits and chain-vape 10-second drags... What tank/RBA are you using, and what resistance is your coil? Are you chain vaping it? is it just WARM or H O T? Which "real" Panasonic batteries are you using? Model? mAh? Details are necessary! Link to comment Share on other sites More sharing options...
Tam Posted August 26, 2014 Share Posted August 26, 2014 Tam, I'll assume Charles' statement was meant for sub-ohming? All the Panasonic batteries I have are rated at 10A, which (in a mechanical MOD) are perfectly safe for any coils over 1.0 Ohms. At 10A limits, the lowest coil these batteries could handle would be 0.45 Ohm, but I'd not trust them on anything lower than 0.8 Ohm (5.25A @ 4.2V), just to give a margin of safety by the "Rule of Two" - Use a battery of at least twice the load/discharge capacity of your expected average load. Now, specs on the Vamo V5 max at 6V, and is limited at 15W, The lowest coil resistance stated it can fire is 1.2 Ohms, and circuitry limits Amp output to 3.2A loads... which means Panasonic batteries are well within the operational limitations of the Vamo V5, and 3.2A should NOT heat up a 10A battery! To JSR27... More info would be handy to have... 10A Panasonic batteries should not be heating up your Vamo even if you push it to it's operational limits and chain-vape 10-second drags... What tank/RBA are you using, and what resistance is your coil? Are you chain vaping it? is it just WARM or H O T? Which "real" Panasonic batteries are you using? Model? mAh? Details are necessary! For my RDAs I only use the Sony VTC4 or VTC5. For tanks like the KPT2 or Nautilus with a 1.8 ohm coil, that's when I use the Panasonic batteries. It's hard to figure out what's being asked when there's not much detail. Link to comment Share on other sites More sharing options...
Earthling789 Posted August 26, 2014 Share Posted August 26, 2014 For my RDAs I only use the Sony VTC4 or VTC5. For tanks like the KPT2 or Nautilus with a 1.8 ohm coil, that's when I use the Panasonic batteries. It's hard to figure out what's being asked when there's not much detail. Exactly! Link to comment Share on other sites More sharing options...
charles vapor Posted August 26, 2014 Share Posted August 26, 2014 Yes I was referring to sub ohming. I should of specified. Link to comment Share on other sites More sharing options...
fishguy1123 Posted August 26, 2014 Share Posted August 26, 2014 Did the OP get this issue figured out? Link to comment Share on other sites More sharing options...
Tam Posted August 27, 2014 Share Posted August 27, 2014 Yes I was referring to sub ohming. I should of specified. Nah, I shouldn't try to post on forums after a grueling 14 hour work day. I don't make much sense and wind up asking all manner of weird questions to try to fill in the blanks in my head. Lol. Link to comment Share on other sites More sharing options...
Compenstine Posted August 27, 2014 Share Posted August 27, 2014 You can't sub ohm on a Vamo..., It won't fire under 1.2 ohms. There is a short somewhere or they are bad batteries. Are you absolutely positive they are legit Panasonic? Please post some pics of the batteries. Link to comment Share on other sites More sharing options...
charles vapor Posted August 27, 2014 Share Posted August 27, 2014 ya, if everything is working right and they are legit panasonics there should be no problem, I use a panasonic with my KFL and nemesis at 1 ohm. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now