Webfoot_Wa Posted May 31, 2014 Share Posted May 31, 2014 Howdy, a question on using the Kanger Pro 2 with my 510 Protected 650mAh, 2.8v pass-through battery from Johnson Creek.. I've noticed the coil (wick) on the pro 2 tank is really short and will not fire up using my fully charged battery..my other tanks (canteens) work fine and the wicks are much longer but not the Kanger..what am I doing wrong? https://www.vaportalkstore.com/Pro-Tank-2-p/pro-tank-2.htm TIA Webfoot_Wa living in New Mexico Link to comment Share on other sites More sharing options...
Tam Posted May 31, 2014 Share Posted May 31, 2014 Do you have a link or a picture of the battery? If you're posting a pic, please take one that shows inside the battery connection. This vid might also be of help. It might be that the KPT2 isn't making connection with the battery, which is why it won't work? Webfoot_Wa 1 Link to comment Share on other sites More sharing options...
Bebop Posted May 31, 2014 Share Posted May 31, 2014 (edited) What do you think he means by "2.8v".? Is that for real? Is that even enough to fire a coil? Or maybe it's a typo? Edit: looks like its a cigalike battery.... Edited May 31, 2014 by Bebop12 Link to comment Share on other sites More sharing options...
Earthling789 Posted May 31, 2014 Share Posted May 31, 2014 Yep, it has nothing to do with the length of the wick... sounds like your battery connection pin is pushed down (as Tam said) or the connection pin of the atomizer head is pushed in... or both... You can also check the center pin on your coil (head, atomizer, whatever you want to call it) and see if it is compressed against the rubber insulator. You can pull it out a TINY bit to make it reach the battery better, but be careful not to pull it too far. Either of these adjustments are MICRO adjustments... it doesn't take much. Webfoot_Wa and Tam 2 Link to comment Share on other sites More sharing options...
Earthling789 Posted May 31, 2014 Share Posted May 31, 2014 What do you think he means by "2.8v".? Is that for real? Is that even enough to fire a coil? Or maybe it's a typo? Probably a typo, but 2.8V "will" fire a coil... but the Wattage/Amps will be extremely low, especially on a higher Ohm coil... so it would take forever to achieve enough heat to produce vapor. Webfoot_Wa 1 Link to comment Share on other sites More sharing options...
Tam Posted May 31, 2014 Share Posted May 31, 2014 What do you think he means by "2.8v".? Is that for real? Is that even enough to fire a coil? Or maybe it's a typo? I'm thinking typo. Not to say they don't make batteries at 2.8v but I've never seen them. More like 3.8v. Link to comment Share on other sites More sharing options...
Bebop Posted May 31, 2014 Share Posted May 31, 2014 Well I looked it up and it is a 2.8v battery. It may not do anything more than warm that coil up..... Link to comment Share on other sites More sharing options...
Earthling789 Posted May 31, 2014 Share Posted May 31, 2014 (edited) Yeah, barely warm... At 2.8V, even using a 1.5 Ohm coil (lowest KPT2 factory coil resistance), that would equate to 5.2 Watts @ 1.9A... hardly enough to vaporize any ejuice, even if you held the button for a full 10-sec. Edited May 31, 2014 by Earthling789 Bebop and Webfoot_Wa 2 Link to comment Share on other sites More sharing options...
Tam Posted May 31, 2014 Share Posted May 31, 2014 The starter kit comes with cartomizers. Wonder what ohm coils those are using so that they'll actually work with a 2.8v battery? Link to comment Share on other sites More sharing options...
Bebop Posted May 31, 2014 Share Posted May 31, 2014 The starter kit comes with cartomizers. Wonder what ohm coils those are using so that they'll actually work with a 2.8v battery? Exactly. They don't say, do they.....hmmmm. Link to comment Share on other sites More sharing options...
Tam Posted May 31, 2014 Share Posted May 31, 2014 Exactly. They don't say, do they.....hmmmm. It must be sooper sekrit ohmage. Bebop and Webfoot_Wa 2 Link to comment Share on other sites More sharing options...
Bebop Posted May 31, 2014 Share Posted May 31, 2014 It must be sooper sekrit ohmage. Thanks for that! Lol (wiping coffee off my lap) Webfoot_Wa 1 Link to comment Share on other sites More sharing options...
Webfoot_Wa Posted May 31, 2014 Author Share Posted May 31, 2014 ahaa, figured it out...it was the way I was putting the 6 pieces together and NOT making a good battery connection..I also thought I wasn't pushing enough at 2.8v but that's not the issue...I am only vaping vg and thought that could be it also but it's working fine now..6 weeks into vaping and off analogs..I really appreciate all the feedback. Link to comment Share on other sites More sharing options...
Webfoot_Wa Posted May 31, 2014 Author Share Posted May 31, 2014 I did take pix but couldn't see where to insert or paste..but that battery connection was the problem Link to comment Share on other sites More sharing options...
Tam Posted May 31, 2014 Share Posted May 31, 2014 Thanks for that! Lol (wiping coffee off my lap) Oooh, did I do that? *whistles innocently. Mtdobies 1 Link to comment Share on other sites More sharing options...
MiamiDan Posted June 5, 2014 Share Posted June 5, 2014 I'd recommend getting an ego style battery or other 510 mod to use instead of the JC battery. IMO the Innokin MVP rocks the protank and is a great bang for the buck upgrade to your vaping. The Vea batteries really are intended only for the Vea cartos and tanks. BTW, the resistance isn't secret since they post it right on the web site. I just measured a JC canteen at 2.65 ohms. How it fires at 2.8 volts is anyone's guess. I still think it's a typo. Has anyone taken a direct measurement of the battery voltage?Glad you got it working though! Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now