cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 The stem would be that rubber piece over top the wicks, correct? And the stuff I have is 50vg Link to comment Share on other sites More sharing options...
Bebop Posted May 18, 2014 Share Posted May 18, 2014 Ok fifty is not bad The stem is the vertical piece that the rubber gasket is around, Remove the rubber gasket. You will see that the stem is press fit into the coil body. Rock the stem off the coil body. This exposes the actual coil and you will see the wicks. Sometimes you end to screw the coil in to the base to remove the stem to get a better hold on it. You can add a small piece of cotton over the top of the coil then press fit the stem back on. Add your rubber seal and give it a shot. If you put too much you can stop the flow so you'll just have to play with it. By the way, this is how I dry burn the coil when it's really gunked up. Remove the stem, set coil up on base and burn it dry Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 Alright, awesome! Thank you! I'll give this a shot when I get home, in the meantime I'll just use the cheapo haha Link to comment Share on other sites More sharing options...
Bebop Posted May 18, 2014 Share Posted May 18, 2014 Haha....good luck Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 Figured I'd check and see if it was still leaking all over the place, blew threw it a couple times, dried it off, set it back down, and now 20 minutes later, nothing. Weird... I'll see if it leaks while I'm using it now quick. Mtdobies 1 Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 So far so good, nothing! Tam and Bebop 2 Link to comment Share on other sites More sharing options...
Mtdobies Posted May 18, 2014 Share Posted May 18, 2014 Yay! Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 Started leaking again, and now stopped again.. but now the battery doesn't seem to be working properly... The led only flashes it's cycle when I turn it on (once red, then once green) and then doesn't do anything, no matter what, unless I plug it in, then it flashes red once, then green a few times, and then stays steady green. I'm already getting fed up with this crap.... I haven't had any issues with the vape I bought at a gas station, for 1/5 the price of this... This is a bit ridiculous. Link to comment Share on other sites More sharing options...
Bebop Posted May 18, 2014 Share Posted May 18, 2014 Okay. Let's back up What voltage do you have it set to? When you press the power button to vape what color does it show? Or, what color does the battery indicator show? Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 3.5 volts, and it doesn't light up at all, it used to light up green. It still seems to be working, but the fact that the led stopped working already has me a little angry to say the least. Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 It says in the manual that it is supposed to fade from red to green when it's charging too, I've only seen red and green, ever, on this thing. Link to comment Share on other sites More sharing options...
Earthling789 Posted May 18, 2014 Share Posted May 18, 2014 3.5V on a 1.5 ohm dual-coil should be pulling 8.2W, which is within the sweet-spot for your battery. A 2.0 ohm coil at that Voltage should pull 6.1W, and that is still within the operational limits of your battery. I have no suggestions on the function issues you're seeing. If the battery is charged fully, based on the Voltage setting you're using, everything should be fine... unless of course the coil has died. Have you tried another coil? Have you tried higher Voltage settings? Say 3.7 - 4.2 range, especially if you're using a 2.0 ohm coil? As for the tank leaking issue... coils are the usual suspect, but I had a ProTank 3 mini leak because the upper/lower rings were not screwed tightly down on the Pyrex tank. This created an air leak (minor one) that allowed the vacuum seal to break, and the wicks were able to constantly wick juice and drip it down onto the battery contact... eventually flooding the entire tube (overnight). This was a horrible surprise on my first hit of the morning I took the tank apart, cleaned it, checked all the o-rings, assembled it snug, replaced the coil and not had a leak since then. Link to comment Share on other sites More sharing options...
cschmall Posted May 18, 2014 Author Share Posted May 18, 2014 The battery seems to be working as it was before again, just no Orange/yellow lights like it's apparently supposed to have I also took the tank completely apart, cleaned everything, I'll see how that goes then. Link to comment Share on other sites More sharing options...
cschmall Posted May 19, 2014 Author Share Posted May 19, 2014 Everything seems to be working properly now, just very very minimal leakage onto the battery. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now