Raptor Vaper Posted July 28, 2014 Posted July 28, 2014 So, I have this problem where I build a good coil and continuously think I can make one that out performs the previous, but then it ends up not being as good and then I can't seem to build the one that was really good anymore lol. lately I have been using dual 26 guage on my nimbus, nothing fancy, but seems to be my most consistant build. I read through these and see all kinds of different stuff (all of which I have tried). Long story shortened, I havent built anything with 24 guage or lower, is it worth a try or should I stick with the hundreds of feet of 28 and 26 guage I have. edit: additionally: what have you guys noticed as far as how the height of the coil from the base effects the build? is it best to keep it as close to level with the air holes as possible, or low to the base? Well I use either 24 or 28 gauge kanthal. I haven't tried 26. But I get tons of flavor off of the 24 gauge. When I build on my dual coil caterpillar rda I do a sleeper coil which is one continuous wire. It heats up much faster because its such a good connection. 5 wraps is my sweet spot for any of my rdas with 24 gauge kanthal. That low resistance though. Less wraps, more heat but less surface area. Just start out with 3 wraps, wick it and vape it. I keep the top of my coil even with the top of my post holes. Also when I wick it, I run a piece of cotton through the coil, wrap the small end under and pull it even with the other side. Then I cut it flush with the rda's edge, then wrap it under. I also push the cotton directly under the coil down to leave a space. If you fire this without the top cap you will notice the vapor shoots in all directions rather than 1. It seems to be enhance flavor and vapor.
Raptor Vaper Posted July 28, 2014 Posted July 28, 2014 Quad coil IGO - W6 build 24 gauge 5 wraps micro coil
Raptor Vaper Posted July 28, 2014 Posted July 28, 2014 Tricro FTW! Oooh nice! I need to try that! How is it?
mvince201 Posted July 28, 2014 Posted July 28, 2014 Fantastic. Flavor is incredible. Oooh nice! I need to try that! How is it?
Raptor Vaper Posted July 28, 2014 Posted July 28, 2014 Fantastic. Flavor is incredible. Awesome! Its two micros on top of a macro right?
mvince201 Posted July 28, 2014 Posted July 28, 2014 (edited) Yes. One micro will have one extra wrap because you have to bring the lead around to go into your post hole. Or half wrap I guess. Edited July 28, 2014 by mvince201
charles vapor Posted July 28, 2014 Posted July 28, 2014 Well I use either 24 or 28 gauge kanthal. I haven't tried 26. But I get tons of flavor off of the 24 gauge. When I build on my dual coil caterpillar rda I do a sleeper coil which is one continuous wire. It heats up much faster because its such a good connection. 5 wraps is my sweet spot for any of my rdas with 24 gauge kanthal. That low resistance though. Less wraps, more heat but less surface area. Just start out with 3 wraps, wick it and vape it. I keep the top of my coil even with the top of my post holes. Also when I wick it, I run a piece of cotton through the coil, wrap the small end under and pull it even with the other side. Then I cut it flush with the rda's edge, then wrap it under. I also push the cotton directly under the coil down to leave a space. If you fire this without the top cap you will notice the vapor shoots in all directions rather than 1. It seems to be enhance flavor and vapor. I just built a coil using everything you wrote like instructions on how to build a lego car (very well described) it vapes a little warm so I have a hard time with deep hits but the flavor is really nice.
Raptor Vaper Posted July 28, 2014 Posted July 28, 2014 I just built a coil using everything you wrote like instructions on how to build a lego car (very well described) it vapes a little warm so I have a hard time with deep hits but the flavor is really nice. Nice! The sleeper coil is hard to perfect. Here is one I did just now. 24 gauge, 6 wraps and using the same wicking method I described That was a 2 second pull
3Rutez Posted July 29, 2014 Author Posted July 29, 2014 Some good center post builds you guys are doing. A real "sleeper" coil has space between the wraps, and also one less wrap on one side if I remember correctly. RiP Trippers had a huge brain fart on that one, much like his pronunciation of UD as "yowd". LMAO. In actuality, these are just simple CP builds, with a single wire, making two coils. :P
3Rutez Posted July 29, 2014 Author Posted July 29, 2014 Well, not "simple", as they take a while to master. Great builds you guys got going!
mvince201 Posted July 29, 2014 Posted July 29, 2014 24g tri-parallel sleeper, now thats a real trick :P
charles vapor Posted July 29, 2014 Posted July 29, 2014 (edited) 6 wrap, 26 guage on my nimbus, seems to be the sweet spot for me edit: I dont know why my picture is upside down. Edited July 29, 2014 by charles vapor
Bushwick Posted July 29, 2014 Posted July 29, 2014 (edited) I've watched the whole "sleeper coil" debate explode on the CCI page. That's part of the thing that bothers me about that page. Everyone is quick to bash and slow to educate. We are all working in this together trying to learn and progress. I just recently learned what an actual Sleeper coil was. lol On a lighter note, Nice build, Charles! Very tidy. Looks like it is producing some nice and dense clouds, too. I hope you are enjoying the build.! Edited July 29, 2014 by Bushwick
Raptor Vaper Posted July 29, 2014 Posted July 29, 2014 I've watched the whole "sleeper coil" debate explode on the CCI page. That's part of the thing that bothers me about that page. Everyone is quick to bash and slow to educate. We are all working in this together trying to learn and progress. I just recently learned what an actual Sleeper coil was. lol On a lighter note, Nice build, Charles! Very tidy. Looks like it is producing some nice and dense clouds, too. I hope you are enjoying the build.! I think the sleeper coil gets the most solid connection that's all I build now until my plume veil comes in ( t-shaped positive post)
mvince201 Posted July 29, 2014 Posted July 29, 2014 Sleepers hold a better connection and prevent uneven heating with a 3-post setup. It's just that simple. Raptor Vaper 1
Raptor Vaper Posted July 29, 2014 Posted July 29, 2014 Sleepers hold a better connection and prevent uneven heating with a 3-post setup. It's just that simple. You couldn't have said it better!
Bushwick Posted August 1, 2014 Posted August 1, 2014 Parallel Twisted 28g. 4 wraps around a 7/64 drill bit. Tests to .4. I haven't contributed to this thread in a while. I felt it was time. Mtdobies 1
mvince201 Posted August 6, 2014 Posted August 6, 2014 (edited) 22 gauge kanthal, 5 wrap, 7/64th diameter. .16 ohm Edited August 6, 2014 by mvince201
SteezeOG Posted August 7, 2014 Posted August 7, 2014 First tried a single coil of 26g gplat wire but 9 wraps only came out to just below .3 and on the new ipv2 50 watt box mod that thing was sucking up the juice and was warmer than I wanted. So went with a dual clapton coil build at just below .5 ohm and set it to 40 watts. It blows clouds.
mvince201 Posted August 8, 2014 Posted August 8, 2014 Trying jigsaw coil tonight. Wish me luck, haha.
Bushwick Posted August 8, 2014 Posted August 8, 2014 Trying jigsaw coil tonight. Wish me luck, haha. Dex' build? Good luck! You're gonna need it!
mvince201 Posted August 8, 2014 Posted August 8, 2014 Dex' build? Good luck! You're gonna need it! Indeed. Looks challenging but I think I can handle it.
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now