3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 It creates way more vapor. This thing hits harder than any other type of coil I have ever tried. Link to comment Share on other sites More sharing options...
loneranger721981 Posted October 21, 2013 Share Posted October 21, 2013 I have tried the twisted. My evic tells me a short every time. Not sure if its too low ohm for it or what is going on. Link to comment Share on other sites More sharing options...
3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 A twisted coil is the equivalent to a dual coil, it halves the ohms. You would need at least a 10-12 wrap micro to be at or above 1ohm. Link to comment Share on other sites More sharing options...
Rixter Posted October 21, 2013 Share Posted October 21, 2013 (edited) A twisted coil is the equivalent to a dual coil, it halves the ohms. You would need at least a 10-12 wrap micro to be at or above 1ohm. Actually, twisted wire doesn't quite cut your resistance in half for a given length. You would think it would be half, but side by side metering shows about a third less resistance. That's because twisting two pieces of wire together adds a little length to both pieces, effectively adding a little more resistance. The tighter the twist, the more resistance you add, but generally you can figure on a third less resistance than untwisted wire. PS - I didn't figure this out on my own. I think it was CascadianExotics. Edited October 21, 2013 by Rixter 3Rutez 1 Link to comment Share on other sites More sharing options...
3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 Thank you Rixter. I was thinking half, but you cleared that up real good for me. Rixter 1 Link to comment Share on other sites More sharing options...
Compenstine Posted October 21, 2013 Share Posted October 21, 2013 (edited) While you might find some Kanthal A-1 locally, I doubt you'll find a hundred foot spool of it (lifetime supply) locally for the price temcoindustrialpower.com sells it for, and shipping is free & extremely fast. They sell 100' spools of 28 gauge for $7.75 and 32 gauge for $4.56. You'll spend that much on just a few feet of it at most places. I use 29g for Genesis RBAs (they were out of 28g when I bought my spool) and 32g for BCC rebuilds (Kanger Protank, EVOD, etc.). Thanks for the Kanthal A-1 Link Rixter, this is way cheaper than where I just ordered from. Thank you 3Rutex and Rixter for the great info on mini coils love learning new stuff, new to me any way. Edited October 21, 2013 by Compenstine Link to comment Share on other sites More sharing options...
iheartvape Posted October 21, 2013 Share Posted October 21, 2013 Hmmm.... Looks like I have something new to try on my RDA. I normally use 30g should I lower the gauge for twisting? Link to comment Share on other sites More sharing options...
3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 No. 30 would work just fine. Link to comment Share on other sites More sharing options...
iheartvape Posted October 21, 2013 Share Posted October 21, 2013 Cool, thanks. I'm gonna have to try one after work today. Link to comment Share on other sites More sharing options...
loneranger721981 Posted October 21, 2013 Share Posted October 21, 2013 Wife just called and I got my vape mail today. Brand new rsst and my flatline juices. I cant wait to get home and start playing. I just hope it came with wick because I dont have any more. Link to comment Share on other sites More sharing options...
3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 My RSST only came with 2 spare O-rings, replacement spring and washer, and 2 spare fill hole plugs. No Kanthal or wick. Might I suggest to give cotton a whirl. I spent $3 at CVS on some Sterile Cotton Balls (First-Aid), and have a lifetime supply of wicks. The RSST is a nice RBA. I ordered an extra tank, even though I don't really vape much juice with high PH levels. Link to comment Share on other sites More sharing options...
loneranger721981 Posted October 21, 2013 Share Posted October 21, 2013 How did you put the cotton thru the coil and into the tank? Have a larger ball at the top like an auto drip? Link to comment Share on other sites More sharing options...
3Rutez Posted October 21, 2013 Author Share Posted October 21, 2013 Pull apart a cotton ball. Using a thin piece, roll it in between your fingers (slightly wetting your fingers may help in the rolling process) until it is at your desired thickness depending on coil diameter. If coil is vertical, leave the top section thicker, so it doesn't slip through the coil and into the tank. You can make it long to reach the bottom of the tank, ensuring you get all the juice in your tank, or you can let it hang 1/8 of the way to utilize the auto-drip method. If you choose to auto-drip, only fill the tank up half way, so you can tilt to saturate the wick and vape away. Some boil the cotton and let air dry for 24 hours, as bright cotton balls are treated with H2O2 to whiten. If you are unsure then you can purchase organic cotton instead. It isn't treated and is more yellow in color. I don't boil mine. All cotton will give off an odd wet rag taste for the first few vapes. I always saturate and burn it a few times to get rid of the cotton taste. After that, the flavor is amazing. Link to comment Share on other sites More sharing options...
Proetus Posted October 21, 2013 Share Posted October 21, 2013 Try the vertical coil with the auto drip setup. Is good stuff, a little hard to do with side airflow tho. Link to comment Share on other sites More sharing options...
loneranger721981 Posted October 21, 2013 Share Posted October 21, 2013 Thank you. I will have to give it a shot and post pictures. Link to comment Share on other sites More sharing options...
Mrwaylon Posted October 22, 2013 Share Posted October 22, 2013 The first one I did, didn't turn out to well I had to use a lighter instead of a mini torch, but the sir draw was very hard I'll have to try again. Got any good pointers for me? Link to comment Share on other sites More sharing options...
3Rutez Posted October 22, 2013 Author Share Posted October 22, 2013 Pot holders, tweezers, kitchen stove.... lol, works for me ATM. What are you building? Micro coil in a KPT? With all the coils I've been throwing at this thread, you really gotta specify. Link to comment Share on other sites More sharing options...
Mrwaylon Posted October 22, 2013 Share Posted October 22, 2013 Pot holders, tweezers, kitchen stove.... lol, works for me ATM. What are you building? Micro coil in a KPT? With all the coils I've been throwing at this thread, you really gotta specify. Trying to do one for a mini davide. I got everything down. But heating the coil up with the lighter didn't do to well the coil didn't stay compressed. Plus it was like burned with black smut per say. But I will get me a mini torch. Link to comment Share on other sites More sharing options...
3Rutez Posted October 22, 2013 Author Share Posted October 22, 2013 Yeah, the lighters don't burn hot enough. You get that soot. It is trial and error with the wick. You gotta find the perfect median, or else you get flooding or no air flow. Link to comment Share on other sites More sharing options...
Mrwaylon Posted October 22, 2013 Share Posted October 22, 2013 Yeah I learned the hard way lol. But you don't get better at something if you keep trying the easy jobs lol. Yeah it was good but the heat and the wick lol. Link to comment Share on other sites More sharing options...
Rixter Posted October 22, 2013 Share Posted October 22, 2013 Mrwaylon and 3Rutez 2 Link to comment Share on other sites More sharing options...
3Rutez Posted October 22, 2013 Author Share Posted October 22, 2013 What, no MAP gas? You heating up mattress coils!?! lol Link to comment Share on other sites More sharing options...
Rixter Posted October 22, 2013 Share Posted October 22, 2013 That puppy will oxidize a SS mesh wick in about two seconds. 3Rutez 1 Link to comment Share on other sites More sharing options...
rcoe Posted October 22, 2013 Share Posted October 22, 2013 What, no MAP gas? You heating up mattress coils!?! lol Mattress coils? I'm gonna need a bigger battery 3Rutez 1 Link to comment Share on other sites More sharing options...
3Rutez Posted October 22, 2013 Author Share Posted October 22, 2013 (edited) One point twenty one Jiggawatts! Bahaha, I said Jiggawatts...... GiggaWatts.... lol Edited October 22, 2013 by 3Rutez rcoe 1 Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now