Bebop Posted September 6, 2013 Share Posted September 6, 2013 Wouldn't you know it. Coil that came with it DOA. But they did supply 2 extras and the first one is ok. First impression - I don't know if it's mass hypnosis or not but this baby tastes good! Is it the glass? The bottom coil? Not sure but, wow. Another notch up in the flavor dept. Actually, pretty darn close to a good 510 dripping atomizer if you ask me. The pull is slightly on the airy side but not bad and nothing a finger over one of the three air holes won't take care of. Very nice! Now for the hard part. Do I have this right? You have to balance the glass on the base while you fill it (and the gap is small). A little tricky to say the least. This is gonna be a little learning curve. The first time i got a little juice on my fingers which made the whole balancing act even tougher. This takes some dexterity, not as friendly as the T2. But the reward is to be experienced. I'm liking this. The drip tip is nice and snug and a swap of a couple tips showed good fit all around. Solid performer so far with a little bit more trouble than the T2 but superior taste. A winner Tam 1 Link to comment Share on other sites More sharing options...
Christie Posted September 6, 2013 Share Posted September 6, 2013 Now All we need is the glass to replace the broken glass with ;lol still havent found it yet And yes filling is a pain .I have gotten a lot all over the place ! I go right to the neddle nose bottle I dont even try to free hand it anymore .But I do love it ! Link to comment Share on other sites More sharing options...
wizard46304 Posted September 6, 2013 Share Posted September 6, 2013 (edited) The draw tightens a bit once used, are you taking the top off of it to fill it? Should be filled from the bottom, the base separates and there are 3 small holes toward the outer edge that you fill it through with a syringe or needle top bottle. They are a bit different to fill but are a great glassomizer. Edited September 6, 2013 by wizard46304 Bebop 1 Link to comment Share on other sites More sharing options...
Bebop Posted September 6, 2013 Author Share Posted September 6, 2013 The draw tightens a bit once used, are you taking the top off of it to fill it? Should be filled from the bottom, the base separates and there are 3 small holes toward the outer edge that you fill it through with a syringe or needle top bottle. They are a bit different to fill but are a great glassomizer. What? Did you think I would read the directions? Lol Duh! Thanks, that's ....much easier although still tricky. See folks, learn something new everyday. Link to comment Share on other sites More sharing options...
wizard46304 Posted September 6, 2013 Share Posted September 6, 2013 Hey, that's why we all come here. Link to comment Share on other sites More sharing options...
wizard46304 Posted September 6, 2013 Share Posted September 6, 2013 Hey, that's why we all come here. Needle tips become your friend with these.Ok, quoting myself now Link to comment Share on other sites More sharing options...
Bebop Posted September 6, 2013 Author Share Posted September 6, 2013 Needle tips, locked and loaded. Link to comment Share on other sites More sharing options...
Bebop Posted September 6, 2013 Author Share Posted September 6, 2013 Now for the hard part. Do I have this right? You have to balance the glass on the base while you fill it (and the gap is small). A little tricky to say the least. This is gonna be a little learning curve. The first time i got a little juice on my fingers which made the whole balancing act even tougher. This takes some dexterity, not as friendly as the T2. Geez, what a noob! Link to comment Share on other sites More sharing options...
wizard46304 Posted September 6, 2013 Share Posted September 6, 2013 I would like to have watched you fill it like that. Tam 1 Link to comment Share on other sites More sharing options...
Bebop Posted September 6, 2013 Author Share Posted September 6, 2013 Lol Link to comment Share on other sites More sharing options...
Tam Posted September 6, 2013 Share Posted September 6, 2013 Couldn't figure out what you were talking about at first. That's funny! And so like something I would do. Link to comment Share on other sites More sharing options...
Bebop Posted September 6, 2013 Author Share Posted September 6, 2013 Where there is a will, there is a way, lol Link to comment Share on other sites More sharing options...
bcartervol98 Posted September 6, 2013 Share Posted September 6, 2013 I used needle tips and syringes at first but now I plug the hole through the mouthpiece with a qtip and fill a ton faster than with the needle tips and syringes and only lose what little bit that soaks up in the QTip. I remove just enough of the cotton so it slides through the driptip. It also cleans the shaft the coil sits in of all the condensation that can collect and run down into the coil. Link to comment Share on other sites More sharing options...
spydre Posted September 6, 2013 Share Posted September 6, 2013 I don't have a mini, myself, I have a full size. Sometimes the draw for me is too airy, but sometimes it works for me. Sometimes it goes airy when the coil is about to go, at least mine, although right now, the coil seems to be fine, so maybe it's just me. To fill it, just hold on to it, rather than trying to balance it. But I would recommend the needle nose. The holes on the full sized ones are okay, but I've never seen the holes on the mini. Link to comment Share on other sites More sharing options...
Recommended Posts