kerk Posted July 12, 2013 Share Posted July 12, 2013 Going to order some coils for my EVOD tanks, but which ohms do I want? They list 1.8, 2.2, and 2.5. What role does resistance play? viewvape 1 Link to comment Share on other sites More sharing options...
blucavvy Posted July 12, 2013 Share Posted July 12, 2013 resistance plays a factor with voltage. what type of device are you using? for me, i use a standard 3.7v ego mostly, and when i pair that with a 1.8ohm carto/clearo etc.... it gives me a warm (not hot), thick vapor. generally the easy way to look at it is, the lower the resistance the warmer the vapor will be. so take for instance a 3ohm carto, you would want to pair that with more of like a 5v device. less than 2 ohms right around 4v is good right around 3 ohms 5 volts is good right around 4 ohms 6 volts is good that's certainly not the case for everyone but it's an easy to remember scale. if you want a warm, thick vapor that's a rudimentary scale. if you want a cooler vape it would look more like less than 2 ohms right around 4.5 volts right around 3 ohms 5.5-6 volts etc..... Tam and viewvape 2 Link to comment Share on other sites More sharing options...
kerk Posted July 12, 2013 Author Share Posted July 12, 2013 resistance plays a factor with voltage. what type of device are you using? for me, i use a standard 3.7v ego mostly, and when i pair that with a 1.8ohm carto/clearo etc.... it gives me a warm (not hot), thick vapor. generally the easy way to look at it is, the lower the resistance the warmer the vapor will be. so take for instance a 3ohm carto, you would want to pair that with more of like a 5v device. less than 2 ohms right around 4v is good right around 3 ohms 5 volts is good right around 4 ohms 6 volts is good that's certainly not the case for everyone but it's an easy to remember scale. if you want a warm, thick vapor that's a rudimentary scale. if you want a cooler vape it would look more like less than 2 ohms right around 4.5 volts right around 3 ohms 5.5-6 volts etc..... Thanks Blu, this is for a Vision Spinner 3.3 - 4.8, with EVOD bottom feeder tank. I run it no higher than 3.5v. Link to comment Share on other sites More sharing options...
blucavvy Posted July 12, 2013 Share Posted July 12, 2013 well if you have a vv device then you can pick pretty much any ohm coil you want and dial your spinner in to what vapes well for you. that's the nice thing about vv, just vape what feels right. you should be good with anything in the range of 1.5-3ohm. Link to comment Share on other sites More sharing options...
Tam Posted July 12, 2013 Share Posted July 12, 2013 My favorite so far has been right at around 2.0 ohm and I vape at 4 volts on my Spinner. That's what works best for me (except I turn it down a bit for fruit flavors). YMMV. Link to comment Share on other sites More sharing options...
ongkee Posted July 12, 2013 Share Posted July 12, 2013 im doing a 1.4ohm 4 volts, works well, its just a juice sucker. Link to comment Share on other sites More sharing options...
IMEDICx90 Posted July 12, 2013 Share Posted July 12, 2013 i vape a 2.4 at around 4.1 to 4.2 volts. its a nice warm vape for me although keep in mind i also smoke pure VG. Link to comment Share on other sites More sharing options...
Jeffb Posted July 12, 2013 Share Posted July 12, 2013 Im the same as Medic, minus the VG. Link to comment Share on other sites More sharing options...
Aquatroy Posted July 12, 2013 Share Posted July 12, 2013 I like the 2.2 EVODD heads, works well on APVs or VV ego type batts, fits KPTs also.. Link to comment Share on other sites More sharing options...
Bebop Posted July 12, 2013 Share Posted July 12, 2013 im doing a 1.4ohm 4 volts, works well, its just a juice sucker. Sometimes I don't understand things and I think maybe I'm missing out on something. I don't see how you can have a 1.4 ohm coil and vape it at 4 volts and not fry everything in sight. I have been using 1.8 - 2.0 ohm coils and I can never seem to jack up the volts beyond 3.5 without getting a burn taste almost right away. But I like to do long slow pulls. Ad that brings up another question. Is there any easy way to measure the actual resistance in a coil with a basic ohm meter? I suppose I could check my battery output as well? Link to comment Share on other sites More sharing options...
Jeffb Posted July 12, 2013 Share Posted July 12, 2013 Yes you can check the ohms of a coil and battery voltage with a meter. Link to comment Share on other sites More sharing options...
Love2VapeDaily Posted July 12, 2013 Share Posted July 12, 2013 I use 2-2.5 ohm coils at around 4.2 volts. If I get near 5 volts it starts tasting burnt almost instantly. I also take long slow mouth hits, sometimes long and slow lung hits. Link to comment Share on other sites More sharing options...
hmontes Posted November 16, 2013 Share Posted November 16, 2013 Sometimes I don't understand things and I think maybe I'm missing out on something. I don't see how you can have a 1.4 ohm coil and vape it at 4 volts and not fry everything in sight. I have been using 1.8 - 2.0 ohm coils and I can never seem to jack up the volts beyond 3.5 without getting a burn taste almost right away. But I like to do long slow pulls. Ad that brings up another question. Is there any easy way to measure the actual resistance in a coil with a basic ohm meter? I suppose I could check my battery output as well? I've made a .32 mm gauge coil at 1.4 ohm for my kanger T3, using ego battery (3.7 V), vapes great, the gauge used for the coil prevents it from burning out, it get's hot if I puff for some time but not too much (i have pulled for 7 - 8 seconds and still haven't experienced any burnt taste), I haven't had any chance to test at 4 V but I don't think it will fry. Also, i added a sterilized 100% cotton wick, this thing is one of my favorite vapes, the flavor from the juice it's better than with the silica wick, the only downside is that you must keep wick moist or you'll taste burnt wick, I just do some quick blows in the mouthpiece to get more juice into the coil and avoid burning the wick. Link to comment Share on other sites More sharing options...
iheartvape Posted November 16, 2013 Share Posted November 16, 2013 if I am using a prebuilt coil such as Kanger I use 2.2, if I am rebuilding on like my RSST I try to stay at 1.4 or 1.8 alot of it will really depend on your technique and your device. on my SVD I use any ohm but prefer the 2.2 on my mech mods I like lower ohm especially with my rebuildables. Link to comment Share on other sites More sharing options...
iheartvape Posted November 16, 2013 Share Posted November 16, 2013 (edited) sorry it posted the previous twice so I edited the duplicate. Edited November 16, 2013 by iheartvape Link to comment Share on other sites More sharing options...
Bebop Posted November 16, 2013 Share Posted November 16, 2013 Hmontes- you can measure res with a basic ohmmeter. Touch leads together first and see if it reads 0. If not, then you will subtract this number from your measurement with the coil. The resistance will change slightly depending on if you measure a dry coil or one already in a wet tank. Wet measurement is most accurate Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now