robv1978 Posted February 23, 2013 Share Posted February 23, 2013 5 wraps @ 1.6 ohms. Jeffb and Uma 2 Link to comment Share on other sites More sharing options...
ninjabat Posted February 23, 2013 Share Posted February 23, 2013 Mega grats on that!! Howz it vapin' for ya?? Link to comment Share on other sites More sharing options...
robv1978 Posted February 23, 2013 Author Share Posted February 23, 2013 Still tastes burnt :-/ I guess I'll see how it goes after a tank full. Seems to be wicking slow. Link to comment Share on other sites More sharing options...
ninjabat Posted February 23, 2013 Share Posted February 23, 2013 What gauge coil are you using?? I only ask because i recently got 33 gauge myself and want about 2.5ohm when i get around to wrapping it. If you did 5 loops I'll probably want a few more than that... No idea about the wicking slow (unless the coil is too tight) what grade mesh did you use?? Link to comment Share on other sites More sharing options...
robv1978 Posted February 23, 2013 Author Share Posted February 23, 2013 30 gauge kanthal wire. I rerolled the wick, I'm not sure what size the mesh is, I bought them prerolled/ oxidized. Link to comment Share on other sites More sharing options...
shakaloha Posted February 24, 2013 Share Posted February 24, 2013 Doing this myself for the first time today..... Link to comment Share on other sites More sharing options...
Uma Posted February 25, 2013 Share Posted February 25, 2013 (edited) Congrats!!! How awesome is this. Sweet! Your wicking is slow? Is the other end of the wick also at a 45% angle? The angle really helps to get the juice slurping. The wick is a little high, above your center post height. When you put the cap on, it might short a bit. Try cutting it either level with or a bit lower than your center post. The OHMs will increase as the coil breaks in. You're going to love how easy it is to just unwrap a coil or two, to get your preferred resistance back. This is so cool. I'm really happy for you!! Edited February 25, 2013 by Uma Link to comment Share on other sites More sharing options...
Uma Posted February 25, 2013 Share Posted February 25, 2013 What type of mod are you using? The electronic ones seem to prefer 1.5 and higher. The mechanical mods prefer even lower. (just be sure to keep track of your battery life level and don't let the life get too low). Link to comment Share on other sites More sharing options...
robv1978 Posted February 25, 2013 Author Share Posted February 25, 2013 Yes it's at a 45° angle, barely off the bottom, using a Vamo. LOL I hope I covered it. :-) Uma 1 Link to comment Share on other sites More sharing options...
Uma Posted February 26, 2013 Share Posted February 26, 2013 Did you pre-season your wick? Sometimes that helps to fast-forward the wicking and flavor. (drip juice on wick, light with bic, let fire die naturally, repeat 2 more times). The wick and coil look nice. I can't tell if there is any airspace around the wick and the wickhole though. Try rolling it just a 100th's of a fraction smaller and see if that helps with the wicking. if it still won't work right, (sometimes this happens even with the pros who've never had it happen before), go ahead and try the silica dangle thread trick. Or the Bluegrass's cotton trick. Good luck! Wish I could help more. Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now