Jeffb Posted November 12, 2012 Share Posted November 12, 2012 Does anyone have one of these? If so, how is it? http://www.vaporkings.com/Variable-voltage-510-eGo-USB-passthrough-p/ego-passthrough.htm Link to comment Share on other sites More sharing options...
mcquinn Posted November 13, 2012 Share Posted November 13, 2012 Isn't that adorable.If the price is right even I would consider one of those.3.0 seems like an odd starting place. Link to comment Share on other sites More sharing options...
willmon22 Posted November 13, 2012 Share Posted November 13, 2012 I think 2.9 is an odd starting place like the provari has. I just have one that is a passthrough that isn't integrated. It goes all the way to 6 volts and I am happy with it. The one that you have here is an affordable one that I have heard is good for the price. But I decided to go for the 30.99 one since it can go to 6 volts instead of just 4.8 maximum. I would say it is worth a try since it is so cheap. Just be aware that it has to be plugged in all the time to use it. It can't be used as a battery as it is integrated in the device and it is nondetachable as you can see in the video on the site. Link to comment Share on other sites More sharing options...
mcquinn Posted November 13, 2012 Share Posted November 13, 2012 (edited) I already know I don't care for more than 4 volts with my preferred liquids.I have some 5 volt and a homemade VV passthrough If I had the desire I can go as high on the voltage as I have wall warts for.3 volts just seems like an almost dead battery unless you are using low resistance I suppose.Since I quit using 801 batteries and started using 14500's a passthrough seems like a hassle with the wire and having to be around an outlet or puter. Edited November 13, 2012 by mcquinn Link to comment Share on other sites More sharing options...
Rixter Posted November 13, 2012 Share Posted November 13, 2012 EmpireMods.com has 'em for $12.99 Link to comment Share on other sites More sharing options...
willmon22 Posted November 14, 2012 Share Posted November 14, 2012 (edited) Here is a video review I found: You can always leave a comment and they might respond to you. Edited November 14, 2012 by willmon22 Link to comment Share on other sites More sharing options...
WillBlack Posted November 17, 2012 Share Posted November 17, 2012 ... I just have one that is a passthrough that isn't integrated. It goes all the way to 6 volts and I am happy with it. The one that you have here is an affordable one that I have heard is good for the price. But I decided to go for the 30.99 one since it can go to 6 volts instead of just 4.8 maximum. How about a link to this? Link to comment Share on other sites More sharing options...
willmon22 Posted November 17, 2012 Share Posted November 17, 2012 I have one too. I will try to make a video and post a complete review if I can. Link to comment Share on other sites More sharing options...
Mike Posted November 18, 2012 Share Posted November 18, 2012 I'd. like to know what type and resistence of atty people are using to vape at 6 volts or anything over 4.8v. I only. go to 5v when I drip on a st. res 510 and I haven't used this setup much lateley. I usually use 2.2ohm clearos at 4.2v or the lr. ones at as low as 3.2v. Link to comment Share on other sites More sharing options...
Rixter Posted November 18, 2012 Share Posted November 18, 2012 (edited) An 8w vape using my 3.5Ω IkenVape HR 901 drip atty requires 5.3v, which only uses a cool 1.5a, effectively lengthing the battery life (and isn't possible on my eGo-C Twist) . The 4.8v that the Twist provides will only take a 3.5Ω atty to 6.5w, which isn't a very warm vape. I could use an atty with less resistance, but that would increase my battery's current draw. By contrast, the same 8w vape using a 2.2Ω clearo only requires 4.2v, but the current is increased to almost 2a, which provides less vape-time per charge, as well as a hot switch because of it's amp limitation. When using a DCT, many vapers almost double these figures (some to 15w, 7.5w per coil) because there's two coils wired in series involved, so the extra headroom definitely comes in handy for those. V² ÷ R = P and V ÷ R = I, wherein V = voltage (in volts), R = resistance (in ohms or Ω), P = power (in watts), and I = current (in amps). Edited November 18, 2012 by Rixter Link to comment Share on other sites More sharing options...
Rixter Posted November 18, 2012 Share Posted November 18, 2012 sorry. had a little too much coffee this morning. Link to comment Share on other sites More sharing options...
willmon22 Posted November 20, 2012 Share Posted November 20, 2012 I really need to learn some of this electrical mumbo jumbo. Maybe I will then know more about posts like that. Anyways I am not sure if there is any atomizer that can actually work with 6 volts without any burnt taste. Unless there happens to be one that is greater than 3 ohms. Or perhaps a dual coil atomizer then it would probably be fine at any ohms but I am not quite certain on that as I only use cartomizers. Link to comment Share on other sites More sharing options...
SextraVaper Posted December 2, 2012 Share Posted December 2, 2012 Does anyone have one of these? If so, how is it? http://www.vaporking...passthrough.htm I bought it twice cause its usefull but both times it broke easily...Bad plastic quality I suppose Link to comment Share on other sites More sharing options...
Recommended Posts
Create an account or sign in to comment
You need to be a member in order to leave a comment
Create an account
Sign up for a new account in our community. It's easy!
Register a new accountSign in
Already have an account? Sign in here.
Sign In Now