Raptor Vaper

Use a coil building calculator to find your desired resistance. Enter either 30 or 32 gauge kanthal and your target resistance. Will tell you exactly how many wraps to do! Wick it with organic cotton. Much better flavor!

Aspire Nautilus mini came in the mail today. Wow what a great tank system! Blows my aerotank out of the water! Even with the new aerotank coils. Airflow control is way better than the aerotank. I also find myself not adjusting the airflow to closed and primer puffing every 3-4 hits. Great vapor production! Looks great on my iTaste VV. The beauty ring is identical to the one that came with my aerotank so I just kept the one from my aerotank on it. Happy vaping everyone!

Here is one. Fired for 30 minutes while the dude was gone. If I so much as leave the room, the battery comes out of my mech mods... Too risky! And they almost never go in my pocket. Before I did a magnetic switch upgrade in my nemesis mech mod, the switch fell apart and fired in my pocket. A .2 ohm quad coil build gets PRETTY hot in your pocket. Took around 30 minutes to cool down. But hey it didn't ruin my coil or wicks!

You couldn't have said it better!

I think the sleeper coil gets the most solid connection that's all I build now until my plume veil comes in ( t-shaped positive post)

I'm doing the best I can!! Haha. Power is watts. I always forget because when I change the wattage on my iTaste, it just says P7.5 or P8.0 etc.... So I kinda went blank!

Ooops! I meant wattage [emoji23][emoji23] And the iTaste VV.

Welllll I went a little crazy. Panzer black hawk mod. This should go great with my new kayfun black edition and my new black plumeveil RDA! "Dominator" RDA. Figured I'd give it a try. It doesn't have post screws. You push them down and insert the coil, they are spring loaded! Oh and I couldn't resist it comes with a drip tip I've never seen before.... Kayfun lite v2 black edition! Pretty cool, the tank can be configured several ways. Fully clear, half clear, completely black.

If you are getting a bad hit from the adjustable airflow, try closing it halfway. It will increase the pressure in the tank and pull more juice to the coils and get you a better hit. On my aerotank I close the air flow half way and set the voltage to 7.5-8.0

Congrats! I'm originally from Minnesota, living in Alabama.

Congratulations on the switch! I noticed the same effects as well! Share your story on freetovape.org! It will possibly keep the fda regulations toned down.

Nice! The sleeper coil is hard to perfect. Here is one I did just now. 24 gauge, 6 wraps and using the same wicking method I described That was a 2 second pull

Awesome! Its two micros on top of a macro right?

Oooh nice! I need to try that! How is it?

Quad coil IGO - W6 build 24 gauge 5 wraps micro coil

Well I use either 24 or 28 gauge kanthal. I haven't tried 26. But I get tons of flavor off of the 24 gauge. When I build on my dual coil caterpillar rda I do a sleeper coil which is one continuous wire. It heats up much faster because its such a good connection. 5 wraps is my sweet spot for any of my rdas with 24 gauge kanthal. That low resistance though. Less wraps, more heat but less surface area. Just start out with 3 wraps, wick it and vape it. I keep the top of my coil even with the top of my post holes. Also when I wick it, I run a piece of cotton through the coil, wrap the small end under and pull it even with the other side. Then I cut it flush with the rda's edge, then wrap it under. I also push the cotton directly under the coil down to leave a space. If you fire this without the top cap you will notice the vapor shoots in all directions rather than 1. It seems to be enhance flavor and vapor.

Nice! Did you build it with one continuous wire? That's the only way I can get a dual 24 gauge coil to fit in my caterpillar RDA

I ended up emailing efest to clear up everything on the purple efest 35a. They sent me over a few pics of the cells, casing and then compared to the Sony. They are not the same battery thankfully

Just remember don't build too low and short out. That's a .00. Never build that low. In fact stay above .2 .3 that is where most batteries are near their limit

Heck yes it is! And that positive post is genius!! Why can't all RDA's have that positive post?

I also build safe. I know my batteries limits and I will not blow up a battery in my face. That's not worth it just to blow some clouds haha

A little too much fun, and I may have had too much to drink looking back on that. But hey I build some hella good coils when I'm drunk

New build guys lol I need a life Holy sheet! .15 ohm build. Lordy lordy it glows bright! 24ga 5 wrap sleeper coil (one continuous wire) Macro coil Hang on let me wick it and vape her The weather forecast predicts a lot of cloud cover tonight! Lol! This is a 2 second puller!

Innokin iTaste VV with a kangertech aerotank. Love the combination. Lasts all the way through the day Oh and there are new coils out for them that are built better. I picked up my first pack today and I'm gonna vape on it and see how it does. I'll report back! If the new coil is better I'll make this a definite recommendation!

5 new 100vg bottles Cheesecake graham crust Strawnana Mango Fresh orange Butterscotch Can't wait to drip all these! Vaping on cheesecake right now... My face explains the flavor YUMMMMM