Raptor Vaper

Just ordered : IPV3 in silver Hells gate dual atomizer mod with 2 atomizers and connector 12 Samsung 25rs Cloud chasers inc Archon RDA Congrevape doge v2 Uncle mikes elixir Blackheart line 120ml of malevolent and aphrodisia Nichrome 80 20 gauge, 24 gauge and 32 gauge(32 for Clapton coils) Cloud chasers inc. 120 ml bottles : roar, hyberbeam and razor leaf Finlys premium drip line 30ml, #2, #3 #5 #6 #7. Really excited to get all my new goodies in and try finlys premium drip line! Here are some links fellas. http://www.cloudycollaborations.com/default.asp http://www.umelixir.com/category-s/1834.htm Hells gate : http://www.umelixir.com/product-p/hellsgate.htm Cloud chasers archon : http://www.cloudycollaborations.com/product-p/cciarda.htm Cloud chasers juice : http://www.cloudycollaborations.com/category-s/110.htm Finlys premium drip line : http://www.cloudycollaborations.com/category-s/111.htm Samsung 25r's : http://www.cloudycollaborations.com/product-p/s25rinr.htm

5 wrap 24 gauge dual parallel coil in my plumeveil. New top cap too!

Well what I was thinking, I usually build my dragon coils with 12-14 wraps. The dual parallel heats up much quicker and has just as much surface area but it only takes 6-7 wraps.

Correct. I just want to try it with a parallel coil build and see how it performs

Anyone ever tried a dual parallel dragon coil??

2 upgrade kits. For my nemesis and my black hawk. Gave my other nemesis upgrade kit to a friend. .2 voltage drop on clones is not bad at all

Talk about a build I will never ever attempt. 4 Strand Parallel Coil Build: http://youtu.be/Cl1Aih_RFe4 Yeah 4 strand 28 gauge parallel

Trooper! I've got to where I cannot stand using 28 ga. Maybe its the kanthal I buy but I find it impossible to work with. Even after torching it its super springy

The kayfun lite has dual air holes and 2 screws on the bottom for adjustable air flow. They come loose very very easy and get stuck in the divets on the top cap. So far this is my only solution. I tightened it down all the way on all my other mods, box mods and it didn't get stuck

That's the constant discharge rate. The pulsing discharge rate is somewhere around 60-65 amps.

Make sure you get those coils centered. I find doing it that way you can get even cotton distribution. I found this to get the best flavor. Make sure the cotton isn't too tight. I cut mine about a 1/8" past the edge of the cup depending on the Atty I'm using. Like on my mutation x, it has a very deep juice well so you can cut it a little bit further from the edge. Wicking is very important. It can make or break your build. I recommend to experiment with the wicks. Try a loose wick then experiment a little. Pretty much it shouldn't be very difficult to slide the cotton through. I use organic cotton and almost always a dual parallel. I get the cotton just tight enough to touch the coils but not so tight that it chokes the coil. Also don't drip straight on the coil. It splatters and un-vaporized hot juice is unpleasant. For a while I couldn't figure out why but I had an awful cotton taste. The wick was way too tight. Re-wicked it and it vapes great

So far my best dual parallel in my mutation X. Can't get the coils quite as clean as in my plume veil but they are close close close! Sitting on top of my dual 18650 unregulated duquit box mod, made from kamagong wood. Two Sony vtc-5 batteries. 4 wraps (8/7 with a parallel). Heats up instantly so hot you can't look at it. Chucks the vapor. Let me get a shot of that

Why thank you! As I said, I adore it. The kamagong wood has a long history behind it. In rip trippers "axis box mod" video he explains the history behind kamagong wood. Nicknamed "iron wood" it is incredibly strong and very beautiful. The only problem is the duquit box mod is hand made, therefore very hard to find. I got so damn lucky finding an authentic one. I had MCM contact the eBay seller for proof of authenticity and even spoke with the seller and MCM over the phone to check for authenticity before dropping $200. It came in in a beautiful box, wrapped up safe and has a cert. Of authenticity. It feels natural to hold. Also you can just tell you have a quality product.

I have the mutation x. I adore it. The positive screw backs off when you pull on the coils to position them but not so much that they come out. 18 airflow holes. Damn. Even a low ohm 5 wrap 24gauge sleeper coil feels like you aren't getting any vapor then, WA-BOOM big ole cloud, in your face flavor and its just awesome. I love my mutation x. I don't see many 454's when I'm out and about. I see tons of plumeveils though... That's about it. I love my plumeveil as well

Its actually the airflow screws. They back out way too easily. The air flow screws get stuck in the milled "nuclear" symbol that is in the top cap of the panzer. Other mods have the milled airflow channels that the screws get stuck in. I know its not the contact pin because I took it all the way out of the panzer and it was still stuck. I'm thinking a piece of tape or even a pre-cut sticker that you could stick to the bottom would fix it. I can make them as well. Just when you need to fill it, either use the top fill method or poke a hole where the juice fill screw is. For a while I hated my kayfun but when it finally came unstuck I started loving it. Every time I used the top fill method it would leak. I'm so happy I can fill it from the bottom. Fresh build, fill it up, no leaking, dropped it on my duquit box mod, looks sick, couldn't be happier.

Guys, don't get your kayfun stuck anymore. Especially on a panzer black hawk. Don't screw it all the way down... Mines been stuck twice and it just randomly comes off. No matter what method you use to get it unstuck it will not come off. It just randomly loosens up.

I'm with you on working on vehicles. I've been doing a few little mods to mine. Its coming together though, next is long travel suspension. That should take up a weekend. Can't find a pic of the engine bay. Damn

This is my duquit box mod by MCM. I believe MCM and MCV are the same people. Its made from kamagong wood just like the axis box mod. Unlike the axis its un-regulated. Holds 2 18650's. I have the mutation x Atty on top and this mod hits so hard. The voltage drop is stupid low. I have a dual parallel 24 ga build in it right now.

I agree!

In-line voltage drop meter came in... Loving it! Ordered 7 bottles of Alpha premium e-juice. Usps broke one of the bottles and it ruined the labels on the other 6. I can kind of make out some of them but the rest are screwed. So now when I find the flavors I like and go to order 100vg 8mg ones, I will have to take a wild guess. Oh and they took 3 weeks to arrive. Absolute worst purchase I've ever came across. All these flavors besides superhero is what I bought. I'll leave some feedback as to the flavors. Ignore the ramen noodle dinner, love those things. Anyway here are the labels

Dual parallel coil 24 gauge 5 wraps. Didn't test on the ohm reader but what an awesome build!

I absolutely love mine. Its been super reliable! It lasts me a 8 hour work day and I charge it and vape on it while in my truck driving home or hanging out with friends

Well I actually carry my dripper with me. I drip and drive. The builds I have give me about 5 hits before a dry hit so at a red light I pull off the top cap, drip it and usually have time for 1 vape. I have a nautilus mini and an iTaste VV when I know I will be too busy to use my dripper.

A few tools. I am just curious as to the voltage drop on all my mods so I bought an inline voltage meter. Also picked up a precision screwdriver kit to center my coils much easier

Loving this duquit box mod. It hits so hard and has such low voltage drop that all it needs is a single coil. I put a parallel 24 gauge coil in it. Macro coil. Jeeeez