GEFFiCART

lol vape mail bumps is another thread

Idk if i'd have an issue with slight bumps. It might be because it's new, but I have to like force my Nemesis in the holder. It's very tight.

the clip as just as the picture shows it basically "hugs" your mod and keeps it in place with silicone covered arms should fit anything that's around a 22mm diameter

I got a Mod Clip with a Carabiner. I'm iffy about it, sometimes I like it sometimes I don't. I also got me a Clear Top Cap for my Igo-W, now that I love.

i have two nemesis clones one SS one Brass both with magnetic switch upgrades, I love them but sometimes theyre hard to get a good grip on because of the streamline make of the nemesis

If you go repetitively without buying anything i'd say it would be rude but other than that its just simply window shopping IMO

please do more research and have necessary tools please pick up an ohm reader of some sort please read the safeties of batters and safe ohms to run per battery

it would be the 5-6 wrap of 28G 30G has more resistance per inch than 28G for example if you're trying to build a 1ohm coil 4-5 wraps on 30G would be equal to 6-7 wrap on 28G now that was an example not direct measurements. maybe factors play into your resistance reading

Not steeping is like getting Heinz ketchup and just squeezing the bottle without shaking it first. You'll get all that ketchup juice that collected on top without shaking instead of thick ketchup. Steeping and shaking daily allows the flavors to mix and settle properly. Juices not steeped and thrown right into a dripper are only getting partial flavor and mixtures.

so many threads about the hammer right now.... lol

I'd go with a Kayfun Lite and I just commented in your other thread about the same topic.. but seeing your comment about the original kayfun I assume you got the chammer [hammer clone]

Surprised no one mentioned about MOD batteries exploding.. Those joytech c-twist and batteries of that nature have built in fuses and safeties. The battery will shut down before causing any damage. [granted you have a good battery] I can also see how charging can cause to heating but just use common knowledge. The big thing is with Mechanical MODs and batteries and people that build their own coils. Batteries are only rated to a certain ohm resistance before its too much for the battery and the battery gets compromised. the battery can leak, expand, and if the gasses cannot escape from the mod, explode. Everyone just please research and vape safely. Don't be reckless in vaping. Especially those who use mechanical MODs. You don't want to build a sub ohm coil and vape it with a 18350. Just Be Safe

did you get the real thing? or the clone?

Unfortunately there isn't a Vapors Toolbox on iOS Yes diameter will affect your ohm readings but if you get the right length of wire you'll get about your desired ohms these readings are can vary but they are measured in ohms/inch Guage | Kanthal A1 | Kanthal A | Kanthal D | Nicrome 60 | Nicrome 80 24 0.18 0.17 0.17 0.14 0.13 26 0.29 0.27 0.27 0.22 0.21 28 0.46 0.44 0.42 0.35 0.34 30 0.72 0.69 0.67 0.56 0.54 32 1.15 1.10 1.07 0.88 0.85

no the magnet is strictly for the use of the firing button. it doesn't pull the battery out because the insulator in the button that makes contact with the batter is thick.

it replaces the 2 springs in the magnet. its supposed to create a smoother even throw and less crunch. magnets were only a couple bucks from china, but the difference is minimal. but its noticeable to me. and when I swapped out the springs for magnets that gave me a chance to thoroughly clean the button. overall outcome made the button smoother, less crunchy, and an even throw whether pressed in the center or near the sides of the button.

what battery are you putting on this KPT?

yeah I made the same mistake when I first started using cotton with my RSST. I put too much and in a sense in choked up the juice from getting to the coil because it was too thick

VapeMail from FT A crap load of drip tips, including but not limited to, white derlin muffler tip, white and black derlin insulators, hybrid drip tips with derlin 510 but SS tip, and a few more drip tips. Also got my magnets for my nemesis, installed those as well. It also gave me time to thoroughly clean my button since I had to take apart the button. I like it a lot. The difference is minimal but good enough for me, I might add a 3rd magnet in there just to increase the resistance

you might be using too much cotton, a little bit of cotton can go a long way. If you haven't already check out RipTrippers on youtube and his video on auto drip mod on genesis style rba's

......I cant believe now we have to wait till February

you going to sell it?

how long did it take for you to get your fast tech order?

yup! that's the purpose of this thread, to keep up to date knowledge of twisted coils and a way to show off your builds!

maybe i'll try it sometime this week my fiancé took my other nemesis on an igo w, she wants an upgrade from her KPT2 lol. i built a tricro coil at work and now i doubt i'll get to put it on with her vaping all the time lol. I gotta pick myself up some more igo-ws