IMEDICx90

Don't sell the kts. Just get more Atties. It's always good to permanently pair them together so you avoid stripping the threads due to constant removal. I'm at a point where I'm finally catching up on mods for my attys lol. I regret selling off the ones I did because I would have rather made it so they were paired with an RDA or an RBA. Unless you are looking to recoup the money for a different purchase. Btw the only other genuine mod I plan on purchasing is the poldiac. I have wanted one since I joined here and drooled over UMA's and that's only becAuse none of the clone I have found have been a great representation of the real deal.

Patricia I wouldn't really worry about it. If your buying huge quantities of it I would say make sure you get through your stash before spending more money on it. I think he was referring to the fact that if wine is not stored properly the cork dries out and allows are into the bottle and it creates a sediment and a vinegar type taste, not the actual eliquid. I have a bottle I have been working on steadily for the last 6 months and it's still the same flavor as when I started it.

No problem spydre glad to help if I can!

No it's just the workout that I'm doing. I'm actually gaining muscle while using the stored fat on my body without cutting into my muscle development. Basically I'm tricking my body into thinking that it's getting more food without spiking my insulin and therefore creating more fat storage. I have been bulking for the better part of a month and now I'm entering a cut phase where it will show me what I have been working on this last month. Then from there I either bulk again or continue with the cut until I'm satisfied with the result and then go into a maintenance type lift. It's not easy gaining mass and burning fat at the same time.

You can do that yes. And you will also want to keep dry burning until the wick turns white again. I know it sounds really dumb but if you can heat it up and get it to start drying out take a toothpick or a needle and lightly scratch at the spots that are brown and it will flake off. Then you can grab a Q-tip and dunk it in a bit of alcohol and lightly wipe the grit away after it's flaked off. a little but more time consuming then just rebuilding, but it will improve your vape 10 fold over just soaking and tossing it back in.

Don't wanna say I told ya so.... But....

The eternity as far as I know doesn't have a tank mode. It does have an extended form but not actually a tank mode. You are overdrippig if it's leaking out and onto/into our battery or hands. And one thing with dripping over a tank is everything is more easily absorbed because the coils are exposed creating a hotter vape. Also the rebuildables you get more throat hit because your directly applying liquid to a coil. you might wanna step down the nic level though. It will take some of the harshness off of it.

Not to mention.... I just consulted my personal trainer and he totally ripped apart my supplement regime.... So now I have: Profusion protien-x4 a day Kreafusion- pre/post workout taken twice a day Animal pax- a multi-vitamin pack that is once a day but there are like 14 pills in each pack..... So yeah... I have been getting hosed in the gym lately lol!

Ok so I have been on a spending spree since the fiancée let me off the leash. I bought the following: Nzonic v4 with a blue gem(sapphire I believe) with a brushed finish. Ba Gua 14500 clone in SS polished Mini DID clone in SS No name RDA for $5 125 ml of EC Blends lemon berry cheesecake 5 pawns sampler pack (would have bought the castle long reserve but that wasn't available) Aqua clone Origin clone (anniversary present) And last but not least IGO W3 and an IGO S. Lol! I think I'm set for a while.

The kraken is by far my favorite right now. The storm rider 2.1 is a close second. I have an aqua and an arrow on the way.... So I'll let you know when they come in lol.

The vertical coil is where it's at. love that stupid thing and it's so freaking easy to redo the cotton surrounding it. I wanna get my hands on some hemp though and try it out.... Just have yet to find it in it's natural form (like Proetus gets). Anyone know where to get it by chance?

That should have been in the last post but it got deleted and it can't seem to add it in. :/

That my friends is a .4 ohm quad dragon coil build before I wicked it up.... It's freaking phenomenal!!!! I would highly recommend this build to anyone with the patience, the outcome is fantastic. I'm tasting my own orange dreamscicle on a totally different level. But beware you need a safe battery!!!!!!!!!

Oh I'm not offended. Lol I was just trying to figure out the math is all. It didn't add it so to speak. And it's the hammer by Kato clone http://www.fasttech.com/products/0/10007023/1569003-hammer-style-mechanical-mod That's the one I'm talking about. I get your ideal and while I will back you up on that 99% of the time, however if it's something I can save literally 50% or more and I don't have to have it right now, I'll grab it from FT.

You think that paying $60 for a hammer clone (rough prices from my limited search) plus shipping here in the states compared to 22.50 on FT is 5-10%? That seems more along the lines of closer to 60% savings in my book and shipping is free.....

You can't burn silica. Well you can but I highly doubt you would be able to heat it to 1600 degrees Celsius with your PV.

Yeah! I would add one small step though between three and four. 3.5.) place a few drops of liquid on the cotton Or you can reassemble and make sure you do a few unpowered draws just to soak the cotton. Unlike silica it will burn really quick, so make sure you get it saturated before vaping it whole hog.

There you go b. that's the spirit! And usually just removing 1 does the trick for me. If they use distilled water in their mix though it still might be too much space in between the stem and the coil. That's why I usually just replace them with cotton.

I would replace one and see if that doesn't fix your issue. Another way I have fixed it is to remove the silica wicks and take some cotton from a cotton ball and use that in place of the flavor wicks. It's a more aggressive wicking material so it seems to help keep the coil pumped with juice but doesn't allow it to flood. but you could just try and add the second flavor wick back in if you don't like the cotton idea. And I use plain cotton balls and never boil them. For Christ sake we are inhaling worse stuff into our lungs when you walk outside. Give me a freaking break about all this "only use boiled cotton" crap. So b just grab a fresh cotton ball out of the package and pull it apart to about the same size as the flavor wicks and lay them on top like your flavor wicks, replace the pressure fit stem, and then put it in the tank. Works like a charm.

What do you mean appear? If you haven't measured it, you wouldn't know the difference. That's fact. I can say anything APPEARS to be one way but unless I can confirm through scientific fact, it's an assumption. I will tell you that what was said about the voltage drop is scientific fact. It will always have a drop in voltage when the is a load applied. That is why people pay big money for the genuine mods because the build quality and materials reduce voltage drop. They have mods that have a measured .015 voltage drop when under load. Just saying. You can agree to disagree but your wrong.

Clones aren't evil. As far as I'm concerned I'm the same way with one exception. The ONLY reason I would buy a real version over a clone is if the performance would drastically improve with the genuine version over the clone, and if it's not an arm and a leg. I wouldn't buy a swan ever (even though it's sweet) because I refuse to pay $1800 for a piece of ******* metal tubing regardless of the hand engraved lines.

Building your coil to a lower ohm and being able to increase the amps pulled from the battery will do the same thing on a mech as it will if you used a VV/VW device. So being able to put watts or volts behind it is irrelevant. If you considering an RBA you could either build it at 2.5 ohms and run it on an APV or you could build it at .6 and run it on a mech, either way it's going to be the same idea. I build all my protank coils to about .8 ohms and I am able to produce the same effect (vapor production, flavor, TH,etc.) as if I used a standard resistance coil on an APV. So really to answer your question there is no hardest hitting tank, it comes down to what you want out of the vape. Rebuilding makes everything (that's rebuildable) work on an even playing field, you just have to decide what you like the look of.

Bought me some ecblends Lemon Berry Cheesecake (125ml) and I'm gonna go pick up a kraken clone tomorrow at a local shop.

Why would you vape without inhaling it into your lungs? There is absolutely no benefit to it. If you pull it into your mouth and then inhale it makes it's a lot less stressful on your throat and lungs.

Well he is right that it's what holds everything in, but you can shimmy it down. I promise I pull them apart everyday. But it's not important if your problem is fixed.