Proetus

Alien Vision Gorilla Juice and Boba's Bounty GLV Deadly Sin Are a few of my favorites. Fadora, already mentioned has some tasty stuff as well.

6.8 amp limit and the protection make it nearly unusable for anything other then vv devices. I wouldn't even use it in a DNA or DNA clone.

Yessir. It isn't magic tho, needs to be set up properly. Taifun GT is a cloud blower also.

He said erection.

Taifun GT clone from slow tech. Works flawlessly, can work on coil w/ a full tank of juice. Big Blu is a dirt n fingerprint magnet. Trying to mitigate that with darker colors and a satin finish.

Finally had some time to solder some stuff up. Had a fight with the epoxy putting the screen cradle in that i lost. So i need to sand and repaint/finish the enclosure. Not impressed with that, however it was my fault for slopping **** around. Oh well be careful with epoxy on satin finishes. Lesson learned. Two day setback due to repainting.

I build and mount mine while still on a blunt needle. Once mounted how I want them, I'll fire them and squeeze with tweezers a few times.

Charging Bag

The 20 is close, the 30 not so much. There is one difiference however. The Yihu chip is a buck/boost converter. Meaning it will raise or lower voltage/wattage to set point. The DNA is a boost converter only, when the wattage would be what the chip determines is below battery voltage, the chip just dump the battery voltage to the atty like a mech mod. You'll see this by your ohms flashing on the DNA display. It doesn't bother me as I am rarely under 13 watts.

Much less powerful then an authentic dna as well. Get what you pay for.

US Laws do not apply in foreign countries. Hence the ability to clone away. But as stated, changed the name, leave off the logo etc, it's not a clone. If you notice fasttech has changed the name of a lot of products to "styled" atty/mod etc.

What about bread ties?

Same thing as always, DNA30 w/ Taifun GT and 18650 Provari w/ KFL

They take alot of power to get going, and are a slow ramp up. Mostly they come in the .3-.5Ω variety. Not up to par with kanthal just yet.

Was a good vapemail day for me!! 4 DNA-30 Boards, 5 1amp charging boards, 5 charging cables, 4 510 top caps, 3 stainless steel and one brass. Time to get busy!

That looks familiar!!

100-120 usually. I make 6 30ml bottles and 1 50ml every week and a half roughly.

The rocket is fair at best IMO. Spend a few extra for a Taifun gt or KFL clone.

Well here it is with the satin acrylic clear on it to protect the paint. Knock off a little of the shinyness but it feels good.

Figured i would measure out the last 2 enclosures i have and get the painting process started in anticipation of getting all the parts to finish em up.

Please ensure that you are following all battery safety when building mods. Would hate to see anyone fry a $50 board or worse yet injure yourself or someone else with an improperly wired device. As far as fuses, Start Here

3D printers are stupid expensive right now. One of the guys from the 'other' forums bought one for 2kish, which was a mid price model. It didn't do to well at making parts. Wasn't worth the price of the material (ink). Pieces from shapeways are pretty much spot on. I you wanted to you could pretty much buy your entire enclosure for there for a little bit of coin. Problem with that tho is that it's a fairly laborious process in order to seal the plastic.

Screen cradles arrived the other day. Had to do a little more fit n finish to the enclosure for it to fit. Was expected since i didn't have it while drilling/filing the holes. I got everything fit and GD does it look fantastic! I have to shoot it with Poly either tonight or tomorrow, i'll start wiring it up after i spray it. Test it for a day or two and i'll be done!

For an hour They aren't all 350. Look around the forums.

Is the aero pin sticking down far enough?