Compenstine

One more post and freedom awaits

Welcome to VT.

LMAO ^^^

I like my drip but, I like my tanks for when I'm on the go. I don't want to fuss with dripping and driving. It harkens back to dropping my lighter on the floor board and almost running off the road trying to get it. LOL There is also the unexpected bumps that make me miss the atty and get juice all over me and my lap or steering wheel.

The IGO W is a Rebuildable Atomizer (RDA) and has no switch. Did you mean Ego - W? You may be better off just getting a new EGO battery. The best place I know to bet one (Switch) is through House of Vapor and yes it shows an EGo - T switch, but they are the same.

As far as Elite Puffs, Not sure about them either. I do know though that using a TM name for their e-liquid will get them in hot water with the company that holds the TM. I suggest looking through the Reviews and you will find many vendors that have good reps and good products.

This refers back to your want to do DIY. I always recommend 100% VG for the NIC base. It is not about vapor output it is because flavorings are mostly PG based. If you use 50/50 nic base you will struggle to get that as an end ratio. You will end up adding more VG thus reducing flavor. If you are going for more flavor in a DIY mix add a higher % of flavoring. 70vg/30pg to 50/50 are good for flavor if you adjust for the higher VG by adding more flavor.

Here is a link to a post I made on exactly what your asking

Whoot! Congrats BC!

It is a fact that when you find a good support group you chances of success are much higher. Welcome to V|T.

I use a 32ga round and .5 Flat twist to build my Kanger coils. It gives better vaopr and flavor than just using 30-32ga. The twist with the flat Kanthal gives more surface area. It also creates valleys or rounded groves that catch juice so you are heating (Vaporizing) more juice. This is a 2x28ga and .9 flat twist (3 Wire Twist) This is a singe 28ga ,9 flat twist. It needs to be a little tighter than is shown. You don't want to see the round wire after your twist is done. This was my first twist with flat wire.

To be honest I'm not sure myself. That is actually a good question. Most 3 coil builds I see are on a 5 pin RDA. 4 - & 1 + . I was referring to each coil having the same ohms. but, I can see what you mean. Now I'm confused. LOL

So long as all coils, no matter the gauge, are the same ohms the imbalance is not an issue. two coils look to be in the posts it is just not a good angle to show this third coil. I don't even see the third coil and wonder where it is. The coil surrounded with cotton would be how you would wick a Dragon coil. It should be pointed up a bit more than it is. Most are set at about a 45 degree angle to the base. What are the Ohms of the three coils? How does it Vape?

I like a twisted coil build of 28ga round and .9 Flat (Tiger coil). I like the vapor and flavor I get from the build.

I did not read it. What I use is 100% pure and Kosher. I have used others in the past that were 99.x and found them to leave a coating (film) in my mouth and throat. (Not saying this will) I question what the .x% of impurities are and those are not listed. Has anyone even received this recently? Last it shows anyone getting it was in 2011. What I see is it did not have great reviews... You get what you pay for.

There goes Tam intimidating the new members again LOL Don't let Tam scare you she is a sweetheart... Just don't get near her hammer! Welcome to V|T

Or a 12v cup cooler...

Heat will degrade the NIC, and it can spoil in a hot Car/Truck. Best thing to do is just take it with you in the summer. I do leave a bottle in my Truck over the winter in the console away from the sunlight.

The first one reminds me of an old hand painted oil lamp shade. Very Nice! Those are some nice looking Drip Tips.

Nice build Crush!

You would have an issue with shorts. I know people use SS mesh for wicking, but the when you role them, you need to make sure there are no loose fray (strands) that can cause a short. The only reason the mesh works is it does have some wicking ability because of weave. I would not risk my equipment on a ss wool.

With ToBH you would know if you were swamping the coil. It would be draining out the air holes. I know because that is what I use. Your wicking looks good and is not too excessive but could be shortened just a tad on the well side. Your one coil could use a tad bit of tightening on the - post side, When you have separations in your coil you will get hot legs and it will kill the performance some.

I couldn't agree more. Though I think it looks cool, I just think it is just too massive and not something that will work for me. The only thing I have that would fire it would be my Akuma. I will stick with my Nautilus & Kick 2 as the Tank setup for the Akuma. I could see it on a 26650 mod, but I just don't see a need for it in my line up at this time.

LP Mid west side here. Welcome to V|T.