Leaderboard

As always Sweet Vapes rocks on customer service. They are sending the right coils and postage to send the others back, all within an hour of sending them an email.

Any time! Just keep us posted. From what I see I really like the looks of this mod, and if the mini is nearly as good, it is going to be really hard to resist buying one of each. I am trying to save money for some test equipment and a new charger...and new batteries, and on and on....But if you give this thing high marks, it may bump some of these "needs"

The D4 and i4 are the same, as far as their charging capability. The D4 has a pretty LCD readout that shows the status of the battery charging, Voltage, etc., but either does the job nicely. I have two of the i4's, and they just work... and for ~ $15/each, you can't beat the price

Cotton has a flash point of 420°.

I just got mine today, Not sure about it yet. I think the Ti coil has more to do with the of Vapor production. I had mine up to 550 temp and getting less vapor than a standard Kanthal coil at 15 watts. I do like the look and feel of it as well, I picked the Bumble Bee Yellow too. Reminds me of the old 60s/70s Mopar Yellow Super Bee. Over all for a daily vape, it is nice. My kit came with a semi clear silicon cover that I will keep on it just to protect the finish and wall plug.

Every Since I started Vaping and making mods I would keep reminding myself that there had to be a better way of handling my growing collection of Batteries. I tried lining them up in a cigar box all nice and neat only to knock them back into a jumbled mess the first time I reached for one. Or go to swap out the battery in a mod and forget which hand I had the charged one in ( I killed way to many brain cells when I was Younger ). So while planing this I knew I wanted it to incorporate my existing charger (works great) keep my batteries organized, and be able to test various sizes of batteries. Then I remembered "THE DRAWER" You know the one (I can't be the only one) It's where you throw all the AAA,AA,C,etc. rechargeable and non batteries that you have ever owned and have no idea which are good or bad. So I had to find a meter that would read down to 1.2 volts (AAA) (most will not show below 2.5 volts). And So this is what I came up with and was finally able to get organized and reigning in "THE DRAWER" was a nice added benefit. And in case you;were curious what the 2 bolts next to the display were for It's for testiing 9 volt batteries.(My younger brother will no longer let me test them my preferred method which was to goad him into sticking the leads on his tongue ). Thank you for viewing as always all questions,critiques, and or comments are much appreciated.

It is on manual...but the lowest this mod can fire is 0.08 from what i read in the manual. That is what this build was reading 0.08 ohms, but when i locked it came out to 0.114 Well now that i fixed this little hiccup jason, this mod is right on the money. High marks in my opinion, just cant do the review right now since i have to leave out on the road again tomorrow.

lowest res is .1... could that be the reason? also, are you on auto or have set it manually?

This stupid update... I posted another reply, and it combined them...a good idea, but can really cause confusion. I found a couple of videos and they do show the resistance lock. Try letting it get to room temp, then put it in temp mode, screw on the atty, push up and down power buttons until it says the resistance is set (just like the ipvD2). I think this will help. I know on my 3 mods that have this feature, it does some crazy things if the resistance is not locked. I have one that doesn't have the feature, but I think it sets it when it asks if it has a new atomizer. If you put a hot atomizer on and say new...temps are way off!

I have had a lot of trouble making dual coils work well in TC. It seems like if everything is not perfectly symetical you get hot spots. That being said, yours seems to be burning pretty much where it should (or shouldn't) in the middle of the coil. I know nothing about the Cloupor, but is there a way to lock the resistance? I know that is a big thing with many mods. If you don't lock it in at room temp it can cause it to run too hot or cool, not accurate at all. (some mods do not have this feature) If that isn't the problem the only other real explanation would be that it is just not very accurate. If you lower the temp to 400 or so and lower your joules does it work ok? I just went and watched pieces of 2 different videos about that mod, and I want one now! I think it would make a great home for my TFv4! Great features, the auto mode, dual 18650 and 80 watts in TC! It does have resistance lock, so let it cool to room temp, then put on the atty, push the up and down power buttons at the same time. This should fix your problem.

http://visionecigarette.com/pdf/How%20to%20identify%20a%20FAKE%20Spinner%20II.pdf This will tell you if it is fake or not

I have no clue but my coil wraps stock/built get that same gunk build up