Leaderboard

Depends on the price... and how they perform. If they're even at least as good as the IPV-mini... I'll probably end up with at least two of them

We're also all a bit cracked, but that's part of our charm.

Once you do what Earthling said (dump juice, clean tank, change coil), then let sit for at least a couple of minutes (five is playing it very safe), to let your wick absorb juice sufficiently. Then, you start at the lowest setting. Vape. Not to your liking? Turn it up a LITTLE. Vape. Repeat until you get a slight burnt taste or a little bit of a harsher vape than you like, then back it down a notch.

Which Kanger coil did you use? The OCC sub-ohm coils for the SubTank? If so, they don't use silica, they use Organic Cotton (which will burn if you don't let them saturate). Tam is correct... once you burn cotton, no matter what you do, it will give a burnt taste, and if you leave it in the tank a while, it will transfer that burnt flavor to the juice, and even a new coil won't help the flavor. Best to dump the juice, clean the tank, and start with a fresh coil if that happens

That's a good idea Earthling. I have a bottle of nicotine and I can just add amount needed to each bottle. The person who gave me the nic sent instructions on how much to add. I just need to order me a marked syringe, Thanks for the advice. Patricia

That sucks maybe allergy? Scollops are my fav here we have Peconic bay scollops some of the best eating around

Yah, for about a week or so, lol... Welcome to the forum!

Welcome to the forum. You should find everything you could need here. If you don't find it, just ask! Tam is right. We're all a bit weird. We normally just hide that side from the new guys for a while.

It does, but more curvy. It looks like it would fit your hand good. You need at least 2 of these Earthling!

There are a couple of great flavors I found a last fall, which were only in 3 or 6 mg, because they were marketed as "dripping juices" (max VG). I asked if they would make a 12 mg, but they declined... So, I thinned them a bit with PG based Nicotine and they worked out very well in a tank. Might be something to consider?

Im gonna share this with you guys. THESE are my world famous canyclams they have been made in the UK and Australia (WORLD FAMOUS) . Place your favorite small clam (shell side up) on the BBQ JUST ENOUGH HEAT TO GET THEM TO OPEN . While waiting for them to open grab your favorite beverage and melt some butter. As the butter is melting mix some bread crumbs and parmajon cheese together Even mix or to taste it dont matter its up too you. Now when clams open up twist off the shellpart with out the meat add a spoon full of butter to the clam part then a spoonfull of the parmajon/bread crumb mixture then a bit more butter on top of that. Go get a new beer wait about about 2 mins take them off then enjoy

On Tuesday, I was vaping outside work and one of my co-workers noticed my gear and struck up a conversation. He realized I was using a Russian 91% and mentioned that he had one that was "junk", and wanted to know if I could use it for parts. Hey, free is free, so I said "sure"... he brought it to me yesterday... in the original box, unopened accessories, and leaking juice like crazy . Last night, I was taking it apart for cleaning, and quickly realized exactly WHY it was such a horrible RTA for him He normally uses KPT2's/Nautilus on a Mech-mod or Vamo, and some shop in/near Lexington, KY talked him into buying it (obviously to make a sale of a $139 RTA)... and this is what the shop built for him... with cotton piled-high around the coil, packed in the chimney! I checked the resistance, and it's a 0.7 Ohm coil... on an RTA where builds are best in the 1.2-1.8 Ohm range (yes, the upper deck is scorched and insulator slightly melted - yes, it is wrapped around the air-hole). I honestly don't see how this thing could to anything but make the deck hot and leak like screen-doors on a submarine I cleaned it up last night, and tonight I'm going to build it RIGHT @ 1.4-1.6 Ohms and organic Japanese cotton... and offer it back to him tomorrow... after-all, it's not his fault the shop is ran/staffed by idiots....

Well, I had to take a break from work to give everyone an update... I tracked him down this morning and handed him the "box"... he sighed heavily and said, "I guess it was too far gone, huh?" I smiled, and opened the box, and showed him the "clean" Russian, and began to explain that I was giving it back to him because there was NOTHING wrong with it (aside from the idiot that sold it to him). He tried to be nice and insist that I keep it anyway, but I told him that I couldn't do that to him (or anyone for that matter)... He had been taken advantage of once already, and there was no reason why he shouldn't ENJOY his purchase, to the fullest extent possible! I took it apart and showed him how parts are supposed to fit, how the coil was built and mounted, etc. I then educated him on using an Ohm meter (showed him how with mine), how to dry-burn the coil (and look for inside-out glow), how to tweak the coil if it gets bent during re-wicking... how to wick it, re-assemble, and how to properly fill (from the bottom). He was so excited to see it properly built, and insisted that we fill it and "take a break" so he could try it out BTW, Comp, he loved your PBFB, and I gave him your website so he can order more He had bought that RTA about a year ago, and it had been sitting in the box (slowly leaking juice) since the day after he bought it Now, he has a fully functional, authentic RTA... and hopefully he's a little more educated as well

I had read about them, and I found a 4 pack on Amazon. I think as I retire my VTC4s I will replace them with -25Rs. I don't use my mechanicals much any more and I think these will work great in my box mods.